What is the width of the external wall deformation joint brickwork?
Masonry requirements for exterior walls: avoid placing heavy loads on walls during masonry, ensure proper light transmission, and maintain even mortar joints. At the interface between walls and beams/columns, clean up any residue or debris. Bricks should be moist before being laid, and masonry should not be completed in one go. It should be done in two to three stages to prevent shrinkage of the mortar, ensuring the wall is fully solid. Also, check the flatness of the wall to avoid excessive or thin mortar layers in subsequent steps.
2. Inspection and treatment of wall holes: Before applying plaster, inspect all wall openings and seal them properly. Uneven areas should be leveled using 1:3 cement mortar. If the area is too thick, apply it in layers. Alternatively, use steel mesh or bonding cloth to reinforce the surface. Ensure that holes left by scaffolding, tower cranes, or construction elevators are cleaned and moistened. Apply a cement slurry coating thoroughly, then fill with dry hard concrete. Fill from both inside and outside, tamping it firmly. The water pipe clamp should be inclined downward at 3°–5°, and the expansion sleeve should be embedded with epoxy resin. Wooden wedges are strictly prohibited. For screw holes on concrete shear walls, chisel around the hole to form a bell mouth, fill with expanded cement mortar, and finally seal with polymer waterproof slurry to ensure a tight seal.
3. Some minor mold and honeycomb surface issues were found on the exterior wall. According to the actual situation, the following repair methods were used: 1. For mold repair, first remove any convex parts that do not meet design or specification requirements. Clean the area thoroughly, then wash the base with a wire brush or pressurized water. Level the surface with 1:2 or 1:2.5 cement mortar, and keep it moist for 14 days. 2. For honeycomb repair (all affected areas are small and have no deep holes), first cut away loose stones and debris from the surface, then clean it. Before repairing, moisten the surface with water. Then apply 1:2 or 1:2.5 mortar, and keep it wet for 14 days.
Masonry requirements for exterior walls: avoid placing heavy loads on walls during masonry, ensure proper light transmission, and maintain even mortar joints. At the interface between walls and beams/columns, clean up any residue or debris. Bricks should be moist before being laid, and masonry should not be completed in one go. It should be done in two to three stages to prevent shrinkage of the mortar, ensuring the wall is fully solid. Also, check the flatness of the wall to avoid excessive or thin mortar layers in subsequent steps.
2. Inspection and treatment of wall holes: Before applying plaster, inspect all wall openings and seal them properly. Uneven areas should be leveled using 1:3 cement mortar. If the area is too thick, apply it in layers. Alternatively, use steel mesh or bonding cloth to reinforce the surface. Ensure that holes left by scaffolding, tower cranes, or construction elevators are cleaned and moistened. Apply a cement slurry coating thoroughly, then fill with dry hard concrete. Fill from both inside and outside, tamping it firmly. The water pipe clamp should be inclined downward at 3°–5°, and the expansion sleeve should be embedded with epoxy resin. Wooden wedges are strictly prohibited. For screw holes on concrete shear walls, chisel around the hole to form a bell mouth, fill with expanded cement mortar, and finally seal with polymer waterproof slurry to ensure a tight seal.
3. Some minor mold and honeycomb surface issues were found on the exterior wall. According to the actual situation, the following repair methods were used: 1. For mold repair, first remove any convex parts that do not meet design or specification requirements. Clean the area thoroughly, then wash the base with a wire brush or pressurized water. Level the surface with 1:2 or 1:2.5 cement mortar, and keep it moist for 14 days. 2. For honeycomb repair (all affected areas are small and have no deep holes), first cut away loose stones and debris from the surface, then clean it. Before repairing, moisten the surface with water. Then apply 1:2 or 1:2.5 mortar, and keep it wet for 14 days.
Jiangsu XC Intelligent Technology Co., Ltd. is a pioneer in the field of industrial segmentation, a comprehensive solution provider that integrates software and hardware development, industrial digital intelligence, and industrial cost reduction and efficiency improvement.CNC Tool Cabinet Manufacturer Announces New Product Line: We are excited to announce the launch of our newest product line, designed to meet the evolving needs of modern CNC machining operations. This innovative line features advanced features and cutting-edge technology to enhance productivity and efficiency.
Industry Expert Joins Our Team: We are thrilled to welcome [Name of Expert] to our team as a [Position]. With their extensive experience in the CNC industry, [Name of Expert] will be instrumental in driving innovation and providing exceptional support to our customers.
Upcoming Trade Show Participation: We will be showcasing our latest CNC tool cabinet solutions at the [Name of Trade Show] from [Start Date] to [End Date]. Visit us at booth [Booth Number] to learn more about our products and services.
Customer Spotlight: [Customer Name] shares their experience with our CNC tool cabinets, highlighting the positive impact on their operations.
External dimensions: 1260mm long; 880mm thick; 1950mm high
Inside grid dimension: 150mm long; Deep 378mm; 177mm high
Screen size: 21.5-inch touch screen
Product color: gray
Spring cabinet capacity: 80 spring cargo lanes, larger can store 1600
Freight lane type: 8 floors * 10 lanes * 20 partitions
Number of grids: 28
Applicable system: card swiping, facial recognition
Power supply: AC220V/50HZ
Intelligent Spring Cabinet,43 Inch Spring Mechanism Storage Cabinet,Storage Cabinet With Spring Mechanism,Spring Operation Tool Cabinet
Jiangsu Xicang Intelligent Technology Co., Ltd. , https://www.xciwarehousing.com