| Home>Bearing knowledge> Data elements and their control that affect bearing life |
Data elements affecting bearing life and its manipulation
Source: China Bearing Network Time: 2013-06-06
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
1 When the martensite high carbon chromium steel in the quenched steel is originally arranged as granular pearlite; in the quenching low temperature tempering condition; the carbon content of the quenched martensite; significantly affects the mechanical function of the steel. The strength and the resistance are at 0.5. % or so; touch fatigue life is about 0.55%; anti-crush can be around 0.44%; when GCr15 steel quenching martensite carbon content is from 0.5% to 0.56%; Failure can be the strongest inductive mechanical function.
It should be noted that the martensite obtained in this case is cryptocrystalline martensite; the measured carbon content is the uniform carbon content. In practice, the carbon content in the martensite is uneven in the microdomain. The concentration of carbon around the carbides is higher than that of the original ferrites away from the carbides; therefore, the temperature at which they start martensite transformation is different; then the growth of the martensite grains and the appearance of the microscopic shape are followed. It becomes cryptocrystalline martensite. It can prevent microcracks which are easy to appear when quenching high carbon steel; and its sub-layout is dislocation-type lath martensite with high strength and resistance. Therefore; only when high carbon steel When the medium carbon cryptocrystalline martensite is obtained during quenching, the bearing parts can obtain the best matrix resistance against failure.
2 Retained austenitic high carbon chromium steel in hardened steel after normal quenching; can be rich in 8% to 20% Ar (residual austenite). Ar in bearing parts has advantages and disadvantages; in order to benefit the disadvantages; Ar content should be appropriate Because the amount of Ar is mainly related to the austenitizing condition of quenching heating; how much it affects the carbon content of quenched martensite and the amount of undissolved carbide; it is difficult to correctly reflect the influence of Ar amount on mechanical function. This; fixed austenitic conditions; using austenite thermal stabilization treatment process; to obtain different amounts of Ar; here we studied the effect of Ar content on the hardness and touch fatigue life of GCr15 steel after quenching low temperature tempering. The increase of austenite content; hardness and touch fatigue life are added accordingly; after reaching the peak, it decreases accordingly; but the peak Ar content is different; the hardness peak is around 17% Ar; and the touch is exhausted The peak value is about 9%. When the experimental load is reduced, the effect of the increase in the amount of Ar on the fatigue life of the touch is reduced. This is because when the amount of Ar is small, the effect on the strength is small; and the effect of toughening is More significant than the reason At the time of Ar; a few deformations of Ar; both the stress peaks are reduced; the deformed Ar processing strengthening and the stress-strain-induced martensitic transformation are strengthened. However, if the load is large, the larger plastic deformation of Ar and the basic understanding part The attack stress gathers and breaks; then the life is reduced. It should be pointed out that the beneficial effect of Ar is necessary to be stable under Ar; if it is spontaneously transformed into martensite; the resistance of steel will be drastically reduced and embrittled.
3 The amount, trace, size and dispersion of undissolved carbide in the hardened steel in the hardened steel; affected by the chemical composition of the steel and the original arrangement before quenching; and affected by the austenitizing conditions; The effect of undissolved carbide on the bearing life is less. The carbide is a hard and brittle phase; in addition to the good wear resistance; the load will be concentrated (especially the carbide is non-spherical) and the matrix will cause stress gathering. And cracking; then will reduce tolerance and fatigue resistance. Quenching of undissolved carbide in addition to its own impact on the function of steel; also affect the carbon content and Ar content and dispersion of quenched martensite; then the function of steel Additional influence. In order to remind the effect of undissolved carbides on the function; choose steel with different carbon content; after quenching, the martensite carbon content is the same as the Ar content and the undissolved carbide content is different; After °C tempering; because martensite has the same carbon content; and the hardness is higher; therefore, the increase of undissolved carbides is not significant for the increase of hardness; the crushing load reflecting the strength and resistance is decreased; Sensitive Touch Number fatigue life was significantly decreased. Thus quench excess undissolved carbides are summarized mechanical function and failure resistance of the steel is harmful. Properly decrease carbon bearing steel article is one of progress using several methods life.
Quenching of undissolved carbides has an effect on the function of the data; scale, tracing, and scattering also affect the function of the data function. In order to prevent the damage of undissolved carbides in the bearing steel; the demand for undissolved carbides is small (less quantity), Ç”å½ç¼§.(16)龋ù笮â€èˆœ 嗖詈 .. 曳 龋 龋 (16) 玻 è“Ÿé”猿 è“Ÿé”猿 è“Ÿé”猿 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 Adhere to the wear resistance of the meet; and is also a necessary condition for obtaining fine-grained cryptocrystalline martensite.
4 Residual stress bearing parts after quenching and tempering After quenching and low temperature tempering; still have large internal stress. Residual internal stress in parts has advantages and disadvantages. After heat treatment of steel parts; followed by residual residual compressive stress Increase; the fatigue strength of the steel increases; the residual internal stress is the tensile stress; then the fatigue strength of the steel decreases. This is because the fatigue failure of the part is presented when the excessive tensile stress is received; When the large compressive stress remains, it will offset the tensile stress of the equality value; and the practice of the steel accepts the tensile stress value minus 蛊@颓慷燃拗翟龈撸,ç »å¬—åŒ—ç »å¬—è–ªæ´—ç½„Î±Î£å†™åª¸ä¿åµŠæ°¤æƒºè‰¿ç¦Î±Ï… testis silly jewel value æ°–Guide food 惺艿ç¦Î±Î³é£¨ 龃螅 龃螅 蛊 颓慷 颓慷 颓慷 颓慷 颓慷 颓慷 颓慷 å› è€Œ å› è€Œ å› è€Œ å› è€Œ å› è€Œ å› è€Œ å› è€Œ å› è€Œ å› è€Œ å› è€Œ å› è€Œ 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承 轴承One of the methods of the number (of course, excessive residual stress can cause deformation or even cracking of the part; it should be given satisfaction).
5 Impurity content of steel Impurities in steel contain non-metallic impurities and harmful elements (acid-soluble) content; their damage to steel function tends to grow with each other; for example, the higher the oxygen content; the more oxide impurities. The influence of impurities on the mechanical function and the failure resistance of the workpiece is related to the type, nature, quantity, size and shape of the impurities; however, it generally has the effect of reducing the tolerance, plasticity and fatigue life.
With the increase of the scale of the impurities; the fatigue strength decreases accordingly; and the tensile strength of the steel is higher; the downward trend is increased. The oxygen content in the steel is increased (the oxide noisy is increased); the tortuous fatigue and the fatigue of the touch fatigue are Under the high stress effect, it also decreases. Therefore, regarding the bearing parts operating under high stress; it is necessary to reduce the oxygen content of the steel for production. Some studies indicate that the MnS impurities in the steel; due to the shape of the ellipsoid, And it can wrap large oxides and noisy, so it has little effect on the decline of fatigue life and even can be beneficial, so it can be manipulated from wide.
The manipulation of the data elements affecting the bearing life is in order to make the above-mentioned data elements affecting the bearing life in the best condition; the primary requirement is to control the original arrangement of the steel before quenching; the technical methods that can be adopted are: high temperature (1050 ° C) austenitizing Rapid cooling to 630 ° C isothermal normalizing to obtain pseudo-eutectoid fine pearlite arrangement; perhaps cooled to 420 ° C isothermal treatment; obtain bainite arrangement. Can also use wrought waste heat blast annealing; obtain fine-grained pearlite arrangement; to ensure The carbides in the steel are finely and uniformly dispersed. The original arrangement of this condition is in the austenitization of quenching heating; in addition to the carbides dissolved in austenite; the undissolved carbides will be aggregated into fine particles.
When the original arrangement in the steel is punctual; the carbon content of the quenched martensite (ie the austenite carbon content after quenching heating), the amount of retained austenite and the amount of undissolved carbide depend primarily on the quenching heating temperature and persistence. Time; followed by quenching heating temperature increase (time must be); steel in the amount of undissolved carbide reduction (hardened martensite carbon content increased), the amount of retained austenite increased; hardness is first added with the increase of quenching temperature; arrival The peak value then decreases with the increase of temperature. When the quenching heating temperature is punctual; the extension of the austenitizing moment; the reduction of the amount of undissolved carbide; the increase of the amount of retained austenite; the increase of hardness; This trend slows down. When the carbides in the original arrangement are fine; because the carbides are easily dissolved into austenite; the hardness peak after quenching is shifted to a lower temperature and appears at a shorter austenitizing moment.
In summary, the undissolved carbides of GCrl5 steel after quenching are about 7%; the retained austenite is about 9% (the uniform carbon content of cryptocrystalline martensite is about 0.55%) is the best arrangement. And; when the original arrangement of fine carbides. Zhi Ji Ren Bao Hui Kang Kang fresh éŠ å— South halo (19) 橹槌墒 挥 诨竦 诨竦 诨竦 诨竦 诨竦 Ï Ï Ï åŸ½ 埽 埽 埽 埽 埽 埽 埽 埽倜. It should be pointed out; the original arrangement with finely dispersed carbides; the quenching heating and heat preservation; the undissolved fine carbides will gather and grow; roughen them. Thus; the quenching heating moment of the bearing parts with such original arrangement Should not be too long; use the rapid heating austenitizing quenching process; will achieve higher inductive mechanical function.
In order to quench the bearing parts after quenching and tempering, the surface has a large compressive stress; the carburizing or nitriding atmosphere can be introduced during the quenching heating; the external carburizing or nitriding is performed in a short time. The practice of carbon is not high; it is much lower than the equilibrium concentration shown on the phase diagram; thus it can absorb carbon (or nitrogen). When austenite is rich in higher carbon or nitrogen; its Ms decreases; when quenching The surface layer has a martensite transformation after the inner layer and the core; a large residual compressive stress is exerted. The GCrl5 steel is heated and quenched in a carburizing atmosphere and a non-carburizing atmosphere (all subjected to low temperature tempering), and the touch fatigue test is performed. It can be seen that the life of external carburizing is 1.5 times higher than that of non-carburizing. The reason is that the surface of carburized parts has large residual compressive stress.
The primary data elements and the degree of control that affect the service life of high carbon chromium steel rolling bearing parts are:
.1) The carbide requirements in the original arrangement of steel before quenching are fine and diffuse. High temperature austenitizing 630 ° C, or 420 ° C high temperature can also be used, which can also be completed by wrought waste heat blast annealing process.
.2) After quenching of GCr15 steel; microscopic arrangement of undissolved carbides with a uniform carbon content of about 0.55% cryptocrystalline martensite, about 9% Ar and about 7% in a uniform and round state This microscopic arrangement can be manipulated using quenching heating temperatures and timing.
.3) After the quenching of the parts, the residual surface has a large compressive stress after the tempering; this will contribute to the progress of the fatigue resistance. The treatment process of carburizing or nitriding in a short time at the time of quenching heating may be selected; There is a large compressive stress.
.4) Making steel for bearing parts; demand has high purity; the first is to reduce the content of O2, N2, P, oxide and phosphide. Optional electroslag remelting; vacuum training and other technical methods to make data oxygen The quantity ≤ 15PPM is suitable.
Recommend to friends comments close window
| Bearing related knowledge |
| The ultimate axial bearing of KOYO bearings can be single row deep groove ball bearings Effect of KOYO Bearing Radial Void Conditioning on Bearing Service Life KOYO outer spherical bearing damage performance mode summary super high speed pneumatic air bearing grinding head spindle |
This article links to http://
Please indicate the bearing network http://
Previous:The basic knowledge of the device of cylindrical hole SKF bearing Next:NSK rolling bearing on the fundamental functional requirements of the data
Graphite Powder soft, dark gray; greasy feeling, can contaminate the paper. Hardness of 1 to 2, along the vertical direction with the increase in the hardness of the hardness can be increased to 3 to 5. Specific gravity of 1.9 to 2.3. In the isolated oxygen conditions, the melting point of more than 3000 ℃, is one of the most resistant minerals. At room temperature, the chemical properties of Graphite powder is relatively stable, insoluble in water, dilute acid, dilute alkali and organic solvents; materials with high temperature conductive properties, do refractory materials, conductive materials, wear-resistant lubricating materials.
Graphite powder is widely used, according to its different use, we can be divided into the following categories of graphite powder
1. Scale graphite powder
Flake Graphite powder is the most widely used, but also processed into other graphite powder of the original material, scaly graphite powder specifications from 32 to -12000 mesh range, scaly graphite powder toughness is good, with good thermal conductivity and corrosion resistance, can be used as refractory Materials, wear-resistant lubricating materials, conductive materials, casting, Fansha, die and high temperature metallurgical materials
2. Colloidal Graphite powder
Colloidal graphite is formed by the average dispersion of graphite particles below 2u meters in an organic solvent. Colloidal graphite is a viscous suspension of black filaments. Colloidal graphite powder with high quality Natural Flake Graphite performance, in high temperature conditions with special oxidation resistance, self-lubricating and plasticity, at the same time with good conductivity, thermal conductivity and adhesion, mainly used in sealing, metallurgical stripping and other industries
3. Ultrafine graphite powder
Ultrafine graphite powder specifications are generally between 8000 mesh -10000 mesh, mainly used in powder metallurgy release agent, the production of graphite crucible, the battery anode and make conductive materials additives
Nano-graphite powder main specifications for the D30 50 100 400 nm, nano-graphite powder process is more complex, low production rate, so relatively high prices, mainly used in anti-corrosion coatings, lubricants additives, grease additives, precision graphite seal And other industries, in addition, nano-graphite powder in scientific research institutions also has a high application value
5, High Purity Graphite powder
Graphite Powder
Graphite Powder,Nano-Graphite Powder,Graphite Carbon,Carbon Brush For Graphite Powder
Fengcheng Ruixing Carbon Products Co., Ltd , http://www.lnfcrxts.com