Decoration tiles are one of the main building materials that are indispensable. Living room floors, kitchens, bathrooms, balconies and other spaces often use it. When tiling, the construction process is stressful, and good craftsmanship can not only make you The smart interior space will save you a lot of money. Secret tile tiles should pay attention to the following aspects.
Cano tile   Carrie bathroom
1. First, clean the back of the pre-selected tiles and soak them for more than 2 hours. The purpose of soaking water is to let the tiles absorb moisture in advance, so as to avoid the moisture in the adhesive material after the plastering, affect the adhesive strength or cause excessive shrinkage of the adhesive material to cause hollowing, de-bonding, and the like. After the tile is immersed in water, it should be taken out from the water before being applied, and the surface moisture can be wiped off with a cotton cloth or the surface moisture can be dried before paving.
2. Before the paving begins, a vertical line should be hung on the wall leveling layer to determine the wall size line of the tile and pull the horizontal line so that the surface can be flat and the tile can be horizontally and vertically.
3. When laying a tile, use a horizontal line as the basis, and set a wooden pallet that supports the tile. The purpose is to prevent the tiles from falling or displacing before the bonding material has hardened to build strength.
4. Paving tiles generally start from the outside corner or from the edge of the door and window, and proceed from bottom to top and from left to right. The method of paving is to wet the screed with water, apply the spliced ​​material to the back of the tile with a small trowel, and then apply the tile to the wall and tap it with a spade with a wooden handle or a rubber hoe. Tiles, so that the adhesive material is full of gaps between the tiles and the wall, pay attention to the top of the tile. The mouth should be aligned with the horizontal line. If it is uneven, you can adjust it by placing a small piece of wood under the tile. After sticking in a row, you should use a ruler to cross it, level it up, knock out the tile that is higher, and remove the paste from the recessed tile.
Bonding materials should not be too thick, otherwise it is not easy to spread, but also should not be too thin, otherwise tile paste can not be fixed, easy to fall down.
5. According to the entire glazed brick wall contamination, scrub the surface with 10% dilute hydrochloric acid solution or tap water. If you use a diluted hydrochloric acid solution, rinse it thoroughly with tap water.
The corners on the wall should be covered with corner tiles, and the inside corners should also be tiled with corner tiles in order to form a beautiful circular arc at the corners. But now people generally for the convenience of the map, the general use of tiles directly touch the angle of the sun corner treatment, the inside corner is generally not to do any treatment.
Tiles Tiles Tiles Tiles Tiles Interiors Window Decorations Living Room Floor Tiles Bathroom Doors Sizes Bathroom Tiles Toilets Bathroom Doors Tiles Floor Tiles Balcony Tiles Kitchen Tiles
Coated abrasives have a wide variety of applications, from grinding applications toLook, one class is the manual use of varieties (sheet emery cloth, sandpaper andPartially rolled sandpaper); The other is for mechanical processing varieties(mainly belt, disc, wheel and ring).
1, large flat surface polishing, steel plate, plywood, leather.
2, mass production of workpiece surface sanding, printed circuit board, steel
Piano board, wooden furniture, etc.
3. Continuous polishing and grinding of metal strip. (Strip width ok
Above 1200mm, length is unlimited)
4, forming grinding and polishing of complex surface work.
5, all kinds of diameter metal tube, rod, roller cylindrical grinding and large diameter
In 25mm container, internal circular grinding such as: cylinder, hydraulic cylinder oil tank
And so on.
6, the page wheel and sand ring can replace polishing cloth wheel, realize polishing process automation.
7. Sand plate is used for grinding welding seam of large shell, box body and hull
Burr, paint, etc.
Coated Abrasive,Flap Wheel,Sanding Paper,Sanding Belts
Henan Jinlun Superhard Material Co., Ltd , https://www.kmgrindingwheels.com