Anti-static mats - laying method foundation ground requirements 1, the ground floor can be smooth surface of the cement floor, terrazzo floors, tile floors, wooden floors. 2, the ground must be flat, no obvious roughness, unevenness should be less than two thousandths of 3, the ground has sufficient strength, no sanding, shelling phenomenon. 4, the ground must be dry.
Construction procedures and specific methods 1. Clean the waste of the ground with a cleaning fluid or xylene (using a cleaning machine) 2. The thickness of copper strips laid on the ground-ground conductive network is 0.02 mm, and the width is 20 mm. The number of strips is based on the actual width of the ground. Measure the length and quantity (the direction of the copper strip is perpendicular to the direction of the anti-static table mat, copper strips are 2-3m apart), and at the same time lead one end of the laid copper strip to the outdoor grounding pole of the earth. The electrostatic table mats are then grounded on the ground. If the gap between the mats is too large, a knife can be used to make the gap smaller. Lay the edges of the laid antistatic table pad on the table mat (about 20cm), apply glue (401 glue or double-sided tape) in the middle of the gap, and let it dry for 20-30 minutes to keep the hands free of sticks (double-sided tape Immediately can be bonded), anti-static table mat bottom (black surface) the same operation (adhesion evenly once, double-sided tape can be painted on the ground, anti-static table mat bottom does not need to stick double-sided tape), and then Anti-static mat and floor adhesion, and then roll with a heavy roller several times, so that the surface of anti-static table mat can be neat and straight (if heavy roller rolling by hand or foot), at room temperature It can be used after 48 hours.
Antistatic Pads - Requirements for Static Grounding of Fixed Equipment
The enclosure of fixed equipment (towers, containers, pumps, heat exchangers, filters, etc.) should be electrostatically grounded. If earth-covered equipment is generally not grounded electrostatically. What are the requirements for electrostatic grounding in static-protected rubber equipment? Anti-static mat manufacturer professionals are how to answer?
1 The enclosure of fixed equipment (towers, vessels, pumps, heat exchangers, filters, etc.) should be grounded electrostatically. If earth-covered equipment is generally not grounded electrostatically.
1 For equipment with a diameter greater than or equal to 2.5m and a volume greater than or equal to 50m3, the grounding point should not be less than two, and the grounding point should be evenly arranged along the periphery of the equipment. The spacing should not exceed 30m.
(2) For the fixed equipment with vibration performance, the vibration part should be grounded with a soft copper conductor with a cross section of not less than 6mm2, and it is forbidden to use single strands. Soft-stranded copper conductors shall be used to bridge across several devices with soft connections.
3 The grounding of the rotating object can be grounded with conductive grease or a special grounding device (such as a slip ring and a brush in a non-explosive, non-fire-hazardous environment), but similar to the valve stem, the rotating part of the bearing may not be necessary. The above connection. For belts or conveyor belts where electric charges can easily accumulate, conductive rubber products should be used.
4 The anti-static grounding brush and protective cover of the belt-driven unit and its belt shall be grounded.
5 Combustible dust bag dust collection equipment, the grounding terminal of the wire woven into the bag body should be grounded.
(6) The contact resistance between the components inside the device, such as the active connection or sliding connection, should be kept below 1000Ω.
7 The fixing equipment and the grounding wire or the connecting wire should be connected by bolts. The connecting terminals can be set on the side of the equipment and on the side or end of the equipment combined metal bearing.
8 Insulated metal parts (such as flanges, hose fittings, nozzles, etc.) should be grounded with a copper-core soft-stranded wire.
Construction procedures and specific methods 1. Clean the waste of the ground with a cleaning fluid or xylene (using a cleaning machine) 2. The thickness of copper strips laid on the ground-ground conductive network is 0.02 mm, and the width is 20 mm. The number of strips is based on the actual width of the ground. Measure the length and quantity (the direction of the copper strip is perpendicular to the direction of the anti-static table mat, copper strips are 2-3m apart), and at the same time lead one end of the laid copper strip to the outdoor grounding pole of the earth. The electrostatic table mats are then grounded on the ground. If the gap between the mats is too large, a knife can be used to make the gap smaller. Lay the edges of the laid antistatic table pad on the table mat (about 20cm), apply glue (401 glue or double-sided tape) in the middle of the gap, and let it dry for 20-30 minutes to keep the hands free of sticks (double-sided tape Immediately can be bonded), anti-static table mat bottom (black surface) the same operation (adhesion evenly once, double-sided tape can be painted on the ground, anti-static table mat bottom does not need to stick double-sided tape), and then Anti-static mat and floor adhesion, and then roll with a heavy roller several times, so that the surface of anti-static table mat can be neat and straight (if heavy roller rolling by hand or foot), at room temperature It can be used after 48 hours.
Antistatic Pads - Requirements for Static Grounding of Fixed Equipment
The enclosure of fixed equipment (towers, containers, pumps, heat exchangers, filters, etc.) should be electrostatically grounded. If earth-covered equipment is generally not grounded electrostatically. What are the requirements for electrostatic grounding in static-protected rubber equipment? Anti-static mat manufacturer professionals are how to answer?
1 The enclosure of fixed equipment (towers, vessels, pumps, heat exchangers, filters, etc.) should be grounded electrostatically. If earth-covered equipment is generally not grounded electrostatically.
1 For equipment with a diameter greater than or equal to 2.5m and a volume greater than or equal to 50m3, the grounding point should not be less than two, and the grounding point should be evenly arranged along the periphery of the equipment. The spacing should not exceed 30m.
(2) For the fixed equipment with vibration performance, the vibration part should be grounded with a soft copper conductor with a cross section of not less than 6mm2, and it is forbidden to use single strands. Soft-stranded copper conductors shall be used to bridge across several devices with soft connections.
3 The grounding of the rotating object can be grounded with conductive grease or a special grounding device (such as a slip ring and a brush in a non-explosive, non-fire-hazardous environment), but similar to the valve stem, the rotating part of the bearing may not be necessary. The above connection. For belts or conveyor belts where electric charges can easily accumulate, conductive rubber products should be used.
4 The anti-static grounding brush and protective cover of the belt-driven unit and its belt shall be grounded.
5 Combustible dust bag dust collection equipment, the grounding terminal of the wire woven into the bag body should be grounded.
(6) The contact resistance between the components inside the device, such as the active connection or sliding connection, should be kept below 1000Ω.
7 The fixing equipment and the grounding wire or the connecting wire should be connected by bolts. The connecting terminals can be set on the side of the equipment and on the side or end of the equipment combined metal bearing.
8 Insulated metal parts (such as flanges, hose fittings, nozzles, etc.) should be grounded with a copper-core soft-stranded wire.
Ductile iron cover, EN124 A15 B125 C250 D400 E600 F900, cast iron with lock system hinge manhole cover
Hebei Kangjin Metal Products CO.,Ltd , https://www.kjmetalproducts.com